How to Send and Receive SMS Using GSM Modem

In this article we are going to learn, how to send and receive SMS using GSM modem which is controlled by Arduino. Let us see, what GSM modem is, how to interface it with Arduino, how to send SMS with the setup.

We are also going to explore what are all applications we can achieve with GSM modem other than sending text message by a human.

What is GSM modem?

GSM stands for Global System for Mobile communications; it is a standard which was developed by ETSI (European Telecommunications Standard Institute) who described the protocols for 2G communication.

It is the first digital protocol for mobile communication which is optimized for full duplex voice communication. In a nutshell full duplex communication means both the parties can send/receive data (or voice) simultaneously.

The GSM protocol also allows transfer of packet data, such as GPRS and EDGE.

SIM800 GSM调制解调器：

GSM modem is a hardware which accepts a valid SIM card (Subscriber Identity Module), basically any SIM will work, which supports GSM protocol and with a network subscription.

它就像没有屏幕和键盘的手机。根据您选择的型号，它具有四个I/O引脚。

两个用于TX和RX（传输和接收），另外两个用于VCC和GND的引脚，这是所有共同的。

它还由RS232端口组成，用于调制解调器和计算机之间的串行通信，但是我们不会在此项目中使用。

It has standard DC power jack, which can be powered from external power sources such as voltage adapters.

It has working voltage ranging from 5 to 12V on DC jack, depending on the model. It has 3 LED indicators, for power, status, and network.

The power LED indicates the presence of power, status LED indicates whether the GSM modem is operating or not, the Network LED indicates the establishment of mobile network.

Initially network LED blinks every one second while searching for network, once it establishes the mobile network it blinks every 3 seconds.

You need to press power button for 2 to 3 seconds for activating the GSM modem, once you done, it latch to the mobile network.

To verify that your GSM modem works, just call the number of which you have inserted the SIM card. You should get ring back tone. If it does, then your module is working fine.

We are going to use SIM800 GSM modem which supports quad-band 850/900/1800/1900 MHz. if you own a SIM900 modem, need not to worry, the program and circuit is compatible in this project.

Now, you would have gained some idea about GSM modem, now let’s learn how to interface it with arduino.

Circuit Diagram:

As you can infer form the diagram, the circuit connection is dead easy. You just need 3 male to female header pins. A USB cable is mandatory in this project, as we are going to communicate via serial monitor.

始终使用外部适配器为GSM调制解调器供电。Arduino的功率不足以用于GSM调制解调器；它甚至可以超载Arduino的电压调节器。

That’s all about hardware part. Now, let’s move to coding.

Program:

//-------------Program developed by R.Girish---------------//
#include
#define rxPin 9 // gsm TX------> arduino 9
#定义txPin 8 / / gsm RX --------> arduino 8
SoftwareSerial mySerial = SoftwareSerial(rxPin, txPin);
char text[150];
字符串消息=“”;
int x;
void setup（）
{
Serial.begin(9600);
while (!Serial){}
mySerial.begin(9600);
delay(1000);
Serial.println("Write your message (with dot at end):");
}
void loop()
{
x=0;
while( Serial.available()>0 )
{
text[x] = Serial.read();
message += text[x];
x++;
if (text[x-1]==46)
{
Serial.println("Your message is sending......");
SendTextMessage();
ShowSerialData();
delay(1000);
Serial.println("r");
Serial.println("Success");
message="";
x=0;
}}}
void SendTextMessage()
{
mySerial.print("AT+CMGF=1r");
delay(1000);
mySerial.print("AT+CMGS="+91xxxxxxxxxx"r"); // Replace x with your 10 digit phone number
delay(1000);
mySerial.println(message);
mySerial.print（“ r”）;
delay(1000);
mySerial.println((char)26);
mySerial.println();
}
void ShowSerialData()
{
while(mySerial.available()!=0)
serial.write（mySerial.read（））;
}
//-------------Program developed by R.Girish---------------//

Don’t forget the dot (.) at every end of the message, otherwise it won’t sent the message to prescribed number in the program. Replace x with your 10 digital phone number in the program. Make sure you have a working SMS plan on your SIM card.

If you are not from India, please change the country code in the program.

例如：

For UK: +44
For US: +1
For Canada: +1
俄罗斯：+7

You can also automate the message which is sent by GSM modem by coding Arduino appropriately. You can receive automated message alerts on your phone such as: anti-theft alert, fire alarm alert, weather alert on your local area etc.

You can even connect to internet with GPRS in GSM modem, but it is subject of another article.

In one of the forth coming articles we will learnHow to Receive SMS Using GSM Modem and Arduino

If you have further questions regarding how to send SMS using GSM Modem , feel free to ask in the comment section.

How to Receive SMS Using GSM Modem

In the above discussion we learned how to send a text message using GSM modem and also discussed the basics the GSM modem.

In this section we will discuss regarding how to receive SMS via serial monitor of the arduino IDE. We are not only going to receive SMS but, also send text message by pressing different keys. For an instant, pressing “s” will send pre-enter text message, pressing “r” will receive real time SMS.

这是作者的原型：

How it Works

使用GSM Moden接收SMS的电路非常简单，您只需要3个男性标头销即可。GSM调制解调器的TX连接到Arduino的PIN＃9，GSM调制解调器的RX连接到Arduino的PIN＃8，并且在GSM和Arduino之间也给出了地面连接。

Always use external power supply for GSM modem, don’t connect 5Vcc from arduino to GSM modem, as there is good chance of overloading the voltage regulator of arduino.

Don’t forget to implement SMS rate cutter or something similar on your SMS subscription for reduction on your SMS expenses.

Otherwise you will end up empty account balance after sending several SMS, since there won’t be any acknowledgement from your cellular provider after every sent SMS, as the SIM card is in the GSM modem.

The only acknowledgement you get is warning SMS, regarding your empty account, so be cautious about you expenses. Now let’s move to coding part this project.

Program:

//-----------------Program developed by R.Girish-------------//
#include
SoftwareSerial gsm(9,8);
void setup（）
{
gsm.begin(9600); // Setting the baud rate of GSM Module
Serial.begin(9600); // Setting the baud rate of Serial Monitor (Arduino)
delay(100);
}
void loop()
{
if (Serial.available()>0)
switch(Serial.read())
{
case 's':
Send();
break;
case 'r':
Recieve();
break;
case 'S':
Send();
break;
case 'R':
Recieve();
break;
}
if (gsm.available()>0)
Serial.write(gsm.read());
}
void send（）
{
gsm.println("AT+CMGF=1");
delay(1000);
gsm.println（“ at+cmgs =”+91xxxxxxxxxx“ r”）;//用手机号码替换X
delay(1000);
gsm.println("Hello I am GSM modem!!!");// The SMS text you want to send
delay(100);
gsm.println((字符)26);/ / o ASCII代码f CTRL+Z
delay(1000);
}
void Recieve()
{
gsm.println("AT+CNMI=2,2,0,0,0"); // AT Command to receive a live SMS
delay(1000);
}
//-----------------Program developed by R.Girish-------------//

输入电话号码

Enter the recipient phone number on “xxxxxxxxxxx” in the program with your country code at the beginning.

Enter the text that you want to send in the program within the quotation mark: gsm.println("Hello I am GSM modem!!!"); // The SMS text you want to send

Compile the program and upload to arduino.

Insert the SIM card and power the GSM modem with external power supply and press the power button for 3 seconds (depending the model), wait for 10 to 20 seconds to establish mobile network, the network LED should blink once in every 3 seconds. If everything is stated above is done, we are ready to go for next step.

现在打开串行显示器，按“ R”，GSM调制解调器准备接收SMS。现在，将任何手机的短信发送到GSM调制解调器上插入的SIM的编号。
The text message should pop up on the serial monitor, something similar to illustrated below:

The “Hello world” is the message sent to GSM modem and the number from which the text message is sent also displayed.

Now, let send SMS to the pre-entered number in the program with pre-entered message. Press “s” and you will see something similar illustrated below: The sent SMS is “Hello I am GSM modem”.

Now, you know how to send and how to receive SMS using GSM modem.